Led Reflective Aluminum Cat Eye Solar Road Stud

Double-sided 6-lamp Led Reflective Aluminum Cat Eye Solar Road Stud
Product parameters of Led Reflective Aluminum Cat Eye Solar Road Stud:
1. Product model: WDM-DD01-2-6Y
2. Product size: 105*105MM
3. Color of lamp beads: red, yellow, blue, green and white
4. Number of lamp beads: 6
5. Red wavelength: 620-625NM
6. Yellow wavelength: 590-595NM
7. Blue wavelength: 470-475NM
8. Green wavelength: 520-525NM
9. White brightness: 18900-22600MCD
10. Protection grade: IP68
11. Shell material: cast aluminum
12. Battery voltage: 1.2V
13. Solar panel: 2.5V
14. Working temperature: -40℃~60℃

15. Working mode: light control (often flashing / always on)

Second, the characteristics of double-sided 6-lamp Led Reflective Aluminum Cat Eye Solar Road Stud:
1. Led Reflective Aluminum Cat Eye Solar Road Stud use 0.25W/2V monocrystalline silicon solar panels. Monocrystalline silicon is a relatively active non-metallic element. In addition to its general characteristics, it has the advantages of high purity and high solar conversion rate .
2. The double-sided 6-lamp Led Reflective Aluminum Cat Eye Solar Road Stud shell design, strong impact resistance, strong and durable. The solar panel is embedded in the aluminum frame, so that it can better absorb solar energy and will not be damaged by rolling.
3. The Led Reflective Aluminum Cat Eye Solar Road Stud use super-bright Taiwan wafer chip beads. The color is eye-catching and the color is clear. It has good visual performance during the day and night, which can attract the attention of drivers. Reduce vehicle speed and improve driving safety on highways.
4. Double-sided 6-lamp solar road studs are available in a variety of colors, and the color of lamp beads and reflectors can be customized according to customer requirements.
5. Double-sided 6-lamp solar road studs have overcharge and overdischarge protection functions.
6. Double-sided 6-lamp solar road studs have good waterproof and dustproof effects, and the protection level can reach IP68.
3. Installation steps of double-sided 6-lamp solar road studs:
1. Installation instructions:

Roadside line (not recommended to be installed in the middle of the road, to avoid excessive impact of the car and damage to the spike)

Installation steps for the Double side 6 lamps solar road studs:
1> Positioning: first determine the installation position with a ruler to ensure that each position is on a straight line, the installation distance and the design requirements are subject to, the installation place should be flat, dry, clean and seamless.
2> Mixing glue: A glue for road studs, B glue for road studs, the ratio of A glue and B glue is 1:1 (for example: A glue 1 kg, B glue is 1 kg). The glue must be stirred evenly and the color should be the same.
3> Glue: The road surface should be cleaned during installation, and the glue should be moderate. Both the bottom surface of the road studs should be adhered to, and the overflow should not be too much. About 40-50 grams of glue should be used for each road stud, and the glue should be applied to the bottom surface of the road signs. Place on the pre-marked location. After installation, clear road debris.
4> Patrol: After two hours, the installed spikes should be checked again.

5> Road closure: It is recommended to close the road for 6 hours to ensure the curing time of the glue.

In addition to Double-sided 6-lamp Led Reflective Aluminum Cat Eye Solar Road Stud, We also produces Other solar transportation products
1. Solar strobe light
2. Solar yellow flashing light
3. Solar sign

4.horseshoe-shaped solar road studs
5. Double-sided 4-lamp solar road studs, etc.

Contact us if you need more details on Solar Road Stud. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Led Road Stud、Aluminum Road Stud. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Road Stud > Solar Road Stud